Service and Maintenance - SMA Solar Instruction Manual - MyBinding.com User Manual PV Analyzer Z100 - Solar Panel Testers Kenmore Stylite Vacuum Manual Manual For Risograph Gr3750 - wsntech.net Skoda Superb Haynes Manual Risograph Repair Manual - TheTexasOutdoors Guardian 1030 Manual Operating Manual - SUNNY BOY 3000TL / 3600TL / 4000TL /. As this risograph gr3750 service manual, it ends taking place bodily one of the favored book risograph gr3750 service manual collections that we have. This is why you remain in the best website to see the amazing books to have. Now you can make this easier and filter out the irrelevant results. HC5500 User’s Manual. HC5500 Console Manual. HC5500 Printer Driver Manual. HC5500 Scanner Manual. HC5500 ComColor Express IS700C Printer Driver Guide. HC5500 ComColor Express IS700C Set-Up Guide. Chakravakam telugu serial all episodes episode. HC5500 ComColor Express IS700C Utility Guide. HC5000: HC5000 Console. HC5000 User’s Manual. HC Navigation Book.
RISO Global portal site. RISO provides high-productivity low-cost printing solutions by world's fastest ComColor Inkjet printer, and 185ppm digital duplicator. Shop at Discount Office Source for the best deal on a Risograph RP-3500 Service Manual and other office supplies at low wholesale prices! Items: 0 items Total: $0.00.
Code: A01
Description: Master feed error
Causes: 201 Master-positioning sensor does not go ON even after the write pulse motor is activated during the master-positioning, master-cut, or master-loading operation. 202 Master-positioning sensor does not go OFF even when the write pulse motor is reversed during the master-positioning or at start of master-making operation. 211 Master-positioning sensor is ON during standby. 214 Master-positioning sensor is ON at the start of master making. 215 Faulty gate-array control for the write pulse motor (motor does not stop within set time).
Remedy: Open the master-making unit and rewind the master material on the master roll, and then reset the master, or turn OFF the power and power back ON.
Code: A02
Description: Master loading error
Causes: 509 Master-loading sensor was OFF when the master was checked at a specified drum angle during the master-loading operation.
Remedy: Pull out the print cylinder and set it back.
Remedy: Pull out the print drum and push it back in.
Code: A05
Description: Master present in the master disposal area
Causes: 304 Master disposal jam sensor was ON at the completion of the master disposal. 312 Master disposal jam sensor was ON at the start of the master making. 315 Master disposal jam sensor was ON after the completion of the recovery movement.
Remedy: Pull out master disposal box and place it back after removing the jammed master in the master disposal area, or turn OFF the power and power back ON.
Code: A06
Description: Check paper feed tray
Causes: 403 Either the upper or lower safety switch of the paper-feed-tray is OFF. Note: This detection is not made when the machine is in low-power-mode (24V OFF).
Remedy: Change the condition of the paper-feed-tray upper/lower safety switches to ON condition, or turn OFF the power and power back ON.
Code: A07
Description: Paper feed error
Causes: 409 Paper-ejection sensor was OFF when the paper should have arrived, and the paper sensor was ON when the machine stopped (Paper misfeed). 412 Paper sensor was OFF three times in succession when a paper misfeed was detected (paper misfeed). 413 Paper sensor was still ON (detecting paper) when the paper should have went out from the sensor. 418 The paper sensor was ON at the start of machine operation when the START button was pressed. 429 Paper feed error (recovery error). 432 Paper sensor was ON when the machine went into paper feed retry movement after a paper misfeed.
Remedy:
Repair Manual Downloads
Error Codes List page 1
Risograph Repair Manual Free
Code: E 01
Description: Main Motor Lock
Causes: Displayed to interrupt the machine operation: 1) If the Drum position A is still detected by the Position A detection sensor 2 seconds after the Main motor started. 2) If the Drum position A hasn’t been detected by the Position A detection sensor within 5 seconds after the Main motor is started.
Remedy: Press ALL RESET button.
Code: E 02
Description: Elevator Motor Lock
Causes: Displayed to interrupt the machine operation: 1) If the actuator of the Elevator upper limit sensor is not raised within 9 seconds after the Elevator motor started to raise the Paper feed tray. 2) If the light path of the Elevator lower limit sensor is not blocked within 9 seconds after the Elevator motor started to lower the Paper feed tray. 3) If the light path of the Elevator lower limit sensor is blocked 2 seconds after the Elevator motor started to raise the Paper feed tray. 4) If the actuator of the Elevator upper limit sensor is still raised 2 seconds after the Elevator motor started to lower the Paper feed tray.
Remedy: Press ALL RESET button.
Code: E 03
Description: Clamp Error 1
Causes: Displayed to interrupt the machine operation: 1) If the actuator of the Clamp safety switch is still depressed 4 seconds after the Clamp solenoid was activated (turned on). 2) If the actuator of the Clamp safety switch has not been depressed within 4 sec. after the Clamp solenoid was released (turned off). 3) If the Angular magnet has not been detected by the Angular sensor (either 0° or 180°) within 8 seconds after the Clamp motor started rotating. 4) If the actuator of the Clamp safety switch is not depressed when the Clamp solenoid is not in operation.
Remedy: Press ALL RESET button.
Risograph Repair Manual Software
Code: E 04
Description: Ink Overflow
Causes: Displayed to interrupt the machine operation: 1) If the Overflow sensor detects excessive ink in the Squeegee unit.
Remedy: Overflow sensor OFF
Code: E 05
Description: Print Positioning Motor Lock
Causes: Displayed to interrupt the machine operation: 1) If the Vertical centering sensor status has not been changed from ON to OFF (or OFF to ON) within 12 seconds after the Print positioning motor started rotating.
Causes: Displayed to interrupt the machine operation: 1) If the Pressure detection sensor status has not been changed from ON to OFF (or OFF to ON) within 8 seconds after the Main motor started rotating.